Product Details:
Minimum Order Quantity | 1 Number |
Opeating Mode | Manual |
Material | SS |
Type | Woven |
40.0 mm | 12.5 mm | |
106.0 mm | 37.5 mm | 11.2 mm |
100.0 mm | 31.5 mm | 10.0 mm |
90.0 mm | 26.5 mm | 9.5 mm |
80.0 mm | 25.0 mm | 8.0 mm |
75.0 mm | 22.4 mm | 6.7 mm |
63.0 mm | 20. 0 mm | 5.6 mm |
53.0 mm | 19.0 mm | 4.75 mm |
50.0 mm | 16.0 mm | 2.36 mm |
45.0 mm | 13.2 mm | 1.18 mm |
Lid and Pan
Product Details:
Minimum Order Quantity | 1 Number |
Material | MS, Brass |
Operating Mode | Automatic |
Driven Type | Electric |
(Soundless) Vibration type cast iron body. Electrically operated Fitted with FHPElectric Motor inside the Body having speed regulator to increase of discrease the vibration. The table sieve shaker having the capacity of 6 test sieves of 20cm.dai(without test sieve and time switch.) Adaptor for 30 cm dia test sieves .
Optional Extra :Product Details:
Minimum Order Quantity | 1 Number |
Surface Tension | 55 dynes/cm |
Capacity | 1000 ml |
Opeating Mode | Manual |
There will be no abrupt changes in the cross section of the hydrometer, that will hinder cleaning or drying or permit air bubble to be trapped. The graduation of hydrometer will be on the basis of liquid having a surface tension of 55 dynes/cm. The graduation lines will be at intervals of 0.0005, every alternate line will extend beyond the shortest lines; every tenth graduation will exceed that of all the intervening lines and will be numbered in full. The basis of the scale will be density (g/ml) at 27' deg C. The maximum permissible scale error on the hydrometer is plus or minus one scale division.
Hydrometer Jar (IS 2720, Part-IV, 1985, section 5.2.1.2)It will be transparent glass with uniform thickness and base size. It will have a mark of 1000 ml capacity with 7 cm dia at a height of 330 mm_+5 mm. Over all height of the cylinder will be about 400 mm without spout
Product Details:
Minimum Order Quantity | 1 Number |
Case Material | Plastic |
Usage | Industry, Laboratory |
Power Type | Electronic |
Product Details:
Minimum Order Quantity | 1 Number |
Material | MS |
Volume | 1000 ml |
Usage | Laboratory, Industry |
Consists of gunmetal mould 100mm dia X 127.3mm height X 1000ml volume, with collar of 100mm dia X 60mm high and drainage base plate, Drainage cap, Metallic clamping ring, two porous stone for base and cap, Dummy plate, air release valve. With a set of three glass stand pipes approx.6mm, 10mm, and 20mm dia X 1 meter length mounted on a wooden board, the end of the glass tube is serrated to connect rubber tube of 3 meter length with pinch cock.
Product Details:
Minimum Order Quantity | 1 Number |
Drive Weight | 65 kg |
Operating Mode | Manual |
Usage | Industry, Laboratory |
Augur are used to collect disturbed solid samples at reasonable depths for laboratory tests Augurs are available in two types and each in different sizes. Blade Type (Post Hole type) Each Augur outfit consists one each of augur head, one meter long rod, Tee piece and handle. Depths of excavating can be increased by using additional extension rods.
1 meter long for 150mm auger.
1 meter long for 100mm/75mm/50mm/38mm
Product Details:
Minimum Order Quantity | 1 Number |
Material | CI, SS |
Operating Mode | Manual |
Design | Standard |
High sensitivity Proving Ring, 250 kg or 500 kg fitted with 0.002 mm dial gauge with certificate in a nice wooden carrying case.
Dial Gauge 0.01mm x 25mm travel.
Product Details:
Minimum Order Quantity | 1 Number |
Material | CI, SS |
Operating Mode | Manual |
Usage | Industry, Laboratory |
Product Details:
Minimum Order Quantity | 1 Set |
Opeating Mode | Manual |
Capacity | 30 KN |
Supply | 230 V |
Proving ring type. Comprises of a hand operated load frame, cap. 30KN (3000 kgf.) screw jack for loading, handle and strain dial gauge bracket, adaptor for proving ring, conical seats and male/female coning tools for 38 mm dial samples. Supplied without proving ring and dial gauge.
Motorised Cum Hand OperatedComprises a screw operated load frame capacity 50 KN (5000 kgf.) with a gear box and motor drive giving 1.25, 1.5 and 2.5mm/min, rates of strain, pair of cone seating, adaptor for proving ring and strain dial gauge bracket. Supplied with one pair of male/female coning tools for 38 mm dia samples but without proving ring and dial gauge. Suitable for operating on 230 volts, single phase AC Supply.
Product Details:
Minimum Order Quantity | 1 Number |
Operating Mode | Manual |
Usage | Laboratory |
Material | SS, MS |
It will consist of metallic cone with half angle of 15' -30 ±15' and 30.50mm coned length. It will be fixed at the end of a metallic rod with a disc at the top of the rod so as to have a total sliding weight of 148± 0.5 gms. The total rod shall pass through two guides. (to ensure vertical movement) fixed to a stand. Suitable provision will be made for clamping the vertical rod at any desired height above the surface of the paste in the trough. A brass trough 50 mm internal diameter and 50 mm depth will be provided as per IS specification resting on M.S.bars.
Optional Accessories Ground Glass : 10mm thick and about 45 cm square or larger rough glass as per IS 2720 (Part V-1985) for mixing soil and water
Spatula : Flexible with blade about 8 cm long and 2 cm wide made from stainless steel material as per IS:2720 (part V-1985)
Evaporating dish : Made from porcelain material having diameter of about 12 to 15 cm with smooth surface as per IS 2720 (part V-1985)
Product Details:
Minimum Order Quantity | 1 Number |
Material | SS |
Maxmum Capacity | 20 kg/cm2 |
Operating Mode | Manual |
Loading Unit, maximum capacity 20 kg/cm2 consisting of a loading yoke connected to a lever arm with a counter- balancing adjustment and having a lever ratio of 1:10, the whole assembly being mounted on a steel frame stand.
Consolidation cell assembly, fixed ring type for testing 60 mm dia x 20 mm thick specimens comprising :
Product Details:
Minimum Order Quantity | 1 Number |
Material | CI, SS |
Operating Mode | Manual |
Usage | Industry |
Product Details:
Minimum Order Quantity | 1 Number |
Operating Mode | Manual |
Type | Digital |
Material | CI, SS |
Product Details:
Minimum Order Quantity | 1 Number |
Material | CI, SS |
Operating Mode | Manual |
Normal Stress Capacity | 8Kg/Sq.cm. |
Supplied with loading yoke with direct and lever for applying load. Normal stress capacity 8Kg/Sq.cm. Load is applied either directly or through a counter balanced detachable lever. Provision is made for the load to be applied either through a steel ball recessed in the loading pad or direct through a boss on the pre calibrated loading. yoke. The loading unit is provided with V strips and roller strips for frictionless movement of shear box housing.
Consists of loading unit, shear box assembly for 60 mm x 60 mm x 25 mm complete with two halves of loading pad, one base plate. All made of gunmetal with two porous stones. Share box housing of gunmetal, specimen Cutter of steel with set of weight to give normal stress of 3 kg/cm2. through lever as follows.
To give kg/cm2. Qty. |
0.05 - 4Nos. |
0.1 - 1No. |
0.2 - 1No. |
0.5 - 3Nos. |
1.0 - 1No. |
Complete set as above but without proving ring and dial gauge.
OPTIONAL ACCESSORIES :Product Details:
Minimum Order Quantity | 1 Number |
Capaacity | 5 ton |
Operating Mode | Manual |
Type | Hydraulic |
It consists of a 5 ton capacity hand operated, hydraulic jack mounted on a suitable frame two plungers, one of 100mm dia and the other of 150mm dia moulds are supplied one thrust plate for 150mm dia and one for 100mm dia specimens are also supplied. Height of thrust plate is adjustable. Set of plunger adaptors thrust plates for 38mm, 50mm and 75mm dia specimen.
Product Details:
Minimum Order Quantity | 1 Number |
Material | CI, SS |
Operating Mode | Manual |
Adaptor plate Diameter | 200 mm |
Comprises of a frame designed for screw jack operation, one each of the adaptor plates and plunger adaptors for 38mm, 75mm, diameter, 100mm diameter, 150mm diameter, specimens and a stand to obtain simultaneously three 38mm diameter samples from one 100mm diameter sample. The adaptor plate which slides a long the slotted supports can be clamped at any desired position by means of locking nuts. Beside this, the tube or mould can be held in position by raising the tube guides and held in position with locking screws. the lead screw movement can be stopped at any predetermined position by tightening the lead screw locking collar. Plunger adaptor for 200mm dia samples. Adaptor plate with 200mm dia hole and device to extract 3 number 38mm dia samples.
Product Details:
Minimum Order Quantity | 1 Set |
Thickness | 3 mm |
Material | SS |
Length | 130 mm |
It shall be of seamless steel tube, 130 mm long and 100 mm internal diameter with a wall thickness of 3 mm, bevelled at one end,( as per section 2.1)
Steel DolleyIt shall be 25 mm high and 100 mm internal dia with a wall thickness of 7.5 mm with a lip to enable it to be fitted on top of the core cutter.
Steel RammerIt shall have solid mild steel foot of 140 mm diameter and 75 mm height with a concentrically screwed 25 mm dia. Solid mild steel staff. The overall height of the rammer including the foot as well as the length of staff shall be approximately 900 mm.
The foot and staff together shall weight approx, 9.0 Kg.
It shall have a blade of stainless steel approximately 200 mm long 30 mm wide (Stainless steel spatula ).
ScraperA steel strip about 300 mm long, 25 mm wid 3 to 5 mm thick with one bevelled edge with suitable to level off ground.
Product Details:
Minimum Order Quantity | 1 Set |
Material | SS |
Available Size | 10cm, 15cm, 20cm |
Usage | Laboratory, Industry |
SAND REPLACEMENT METHOD: Three sizes Available.
10cm (Small Size) :-
Sand Replacement Method. Consists of Sand Pouring Cylinder, one calibrating container 10 cm dia a square tray of 30 cm x 30 cm with a central hole of 10 cm diameter. Relevant Standard : IS : 2720(Part-XXVIII)
15cm (Medium Size) :
Sand Replacement Method. Consisting of Sand Pouring Cylinder container metal tray hole in the centre.
20cm (Large Size) :
Sand Replacement Method. with calibrating container of 250mm internal depth, one metal tray 450 mm square and 50 mm deep with a 200 mm dia hole in the centre.
Product Details:
Minimum Order Quantity | 1 Set |
Material | CI |
Capacity | 10000 kg |
Operating Mode | Manual |
Mechanical screw loading jack, 10,000 Kg. Capacity with U-bracket and swivel head. Penetration piston, 50mm dia threaded at the upper end. Extension rods set consisting of length 50cm, and 1 length 100cm., used as spacers between the proving ring and penetration piston. The lengths are machined from steel tubing.
Connector set, has eight connectors for coupling the penetration piston and proving ring assembly either directly or through extension pieces.
Dial gauge support of seamless pipe construction. It stands 30cm high and 45cm wide at the base. Provided with a quick release screw type clamp capable of sliding and locking anywhere along 2 meter length of the bridge. Supplied with annular metal weight 5Kg. 250mm dia with 53mm dia central hole, slotted metal weight 5 Kg, 215mm to 250mm dia with 53mm dia slot, 3 Nos, Slotted metal weight, 10Kg, 215mm to 250mm dia with 53mm dia slot. 2Nos.
Product Details:
Minimum Order Quantity | 1 Set |
Driven Type | Manually/Electrically |
Operated Capacity | 5000 kg |
Material | Mild Steel |
Complete with Load frame, Hand Operated/Electrically Operated 5000 Kg capacity, C.B.R. Mould, Penetration Piston, Perforated Plate, Displacer Block, Anuular/Slotted Metal Weight 2.5 kg, Metal Tripod Stand, Rammer 2.6 kg/4.89 kg., with Calibration Certificate.
Optional Accessories :Product Details:
Minimum Order Quantity | 1 Number |
Operating Mode | Manual |
Case Material | Wooden |
Usage | Laboratory |
Consists of a torque head adjustable in height by means of a lead screw rotated by a drive wheel to enable the vane to be lowered into the specimen. Rotation of the vane is by means of a hand wheel which operates a worm gear arrangement turning the upper end of a calibrated torsion spring. Vane dia, rod dia, vane size vane height are as per IS specification.
The Vane shaft is attached through the hollow upper shaft to resettable pointer, which indicates the angle of torgue on a dial graduated in degrees. The dial reading multiplied by spring factory gives the torque. A container for soil tube of 38mm I.D. 150 mm long can also be used as container. Complete with set of springs, one each of approx 0.2kg/cm,4kg/cm,6 kg/cm,8 kg/cm in a nice teak wooden carrying case.
Complete with set of springs, one each of approx 0.2kg/cm, 4kg/cm,6 kg/cm,8 kg/cm in a nice teak wooden carrying case. but with motorised, rate of rotation is 1/60 RPM.
Product Details:
Minimum Order Quantity | 1 Number |
Operating Mode | Manual |
Material | Brass, MS |
Voltage | 230 V |
With consists of a brass cup held on an adjustable bracket. The bowl can be adjusted for a fall raised dropped on a rubber of standard hardness by cam action. Complete with one casagrande grooving tool, one ASTM grooving tools and a height gauge block. Hand operated, with counter. As per IS : 2720 (Part-V), IS : 9259, BS : 1377, AS : 89
Motorised ModelWith consists of a brass cup held on an adjustable bracket. The bowl can be adjusted for a fall raised dropped on a rubber of standard hardness by cam action. Complete with one casagrande-grooving tool, one ASTM grooving tools and a height gauge block. With counter. Fitted with a motor geared down to give approximately 120 RPM. Suitable for operation on 230 Volts, single phase, 50 cycles, A.C. supply.
Product Details:
Minimum Order Quantity | 1 Set |
Glass plate size | 20cm X 15cm |
Material | Brass or stainless steel |
Porcelain basin diameter | 150 mm |
The Complete set consists of one each :
Packed in nice polished wooden box
Product Details:
Minimum Order Quantity | 1 Number |
Material | MS |
Capacity | 1000 cc, 2250 cc |
Usage | Laboratory |
It will be made of Mild steel having capacity of 1000 cc with an internal diameter of 100 + 0.1 mm and an internal effective height of 127.3 cm + 0.1 mm. The mould will be fitted with a detachable base plate and removable extension collar approximately 60 mm high. The internal surface of the mould will be smooth. It will conform to the requirements given in the IS 2720 (Part VII). Complete with our own test certificate.
Light Rammer2.6 Kg x 310 mm fall. A metal chrome plated rammer having 50 mm dia. Circular and weighing 2.6 kg. The rammer will be equipped with a suitable arrangement for controlling the drop to the specified height of 310 mm. It will conform to the requirement given in the IS 2720 (Part VII), IS 9198.With our own test certificate.
2250 ccIt will be made of Mild steel having capacity of 2250 c.c with an internal diameter of 150 + 0.1 mm and an internal effective height of 127.3 cm + 0.1 mm. The mould will be fitted with a detachable base plate and removable extension collar approximately 60 mm high. The internal surface of the mould will be smooth. It will conform to the requirements given in the IS 2720 (Part VII). Complete with our own test certificate.
Heavy Rammer4.89 Kg x 450 mm fall. A metal chrome plated rammer having 50 mm dia. Circular and weighing 4.89kg. The rammer will be equipped with a suitable arrangement for controlling the drop to the specified height of 450 mm. It will conform to the requirement given in the IS 2720 (Part VII), IS 9198.With our own test certificate.
Product Details:
Minimum Order Quantity | 1 Set |
Case Material | Wooden |
Usage | Soil Testing Equipment |
Calibration Range | 0 to 40 kgs |
The Instrument consist of needle attached to a spring loaded plunger. the stem of which is calibrated to read 0 to 40 kgs in 1 kg division. Long stem is graduated at every 12.5mm to read depth of penetration and for use with needles of larger areas. The small penetration steam is also graduated in 12.5mm division and is used with needles of smaller areas. Needle points one each of 0.25, 0.5, 1.0,1.5,2.0, 3.5, and 6.0 sq.cm. and one tommy pin is supplied. Complete as above in a wooden carrying case.
Product Details:
Minimum Order Quantity | 1 Number |
Capacity | 5 kN |
Material | SS |
Operating Mode | Manual |
These proving rings are made out of special steel, carefully forged to give maximum strength machined to give the highest sensitivities commensurate with high stability and to ensure long life and accuracy. All proving rings are integral type viz. the loading (outside) bosses are forged integral with the ring body. This ensures that there is no possibility of abutment shift and consequent loss of accuracy in reading that always exists in rings with bolted abutments. The dial gauge and anvil are mounted on U-brackets clamped to the ring body by Allen set screws. The dial gauge is fitted with a special back cover and threaded bush which does not permit any shift from the original diametric alignment, coaxial with the loading boss centers, that is set at the factory before calibration. For all compression proving rings and tension compression proving rings up to and including 5 kN capacity (a little over 500 kgf) the loading bosses have female threading, 1/2" B.S.F. (16 t.p.i.) The boss faces are ground and polished and are lane parallel to within 0.02mm.total D.T.I. run-out. Caps are provided for use when loading in compression. Repeatability is as stipulated in IS : 4169-1967. The rings are supplied complete with dial gauge and our own calibration chart, packed in polished wooden boxes.
Compression Proving Ring From any capacity to
250 kgf. |
500 kgf. |
1000 kgf. |
3000 kgf. |
5000 kgf. |
2000 kgf. |
10000 kgf. |
20000 kgf. |
25000 kgf. |
50000 kgf. |
100000 kgf. |
200000 Kgf. |
Product Details:
Minimum Order Quantity | 1 Number |
Case Material | Wooden |
Operating Mode | Manual |
Usage | Accurate measurement of moisture and temperature |
Product Details:
Minimum Order Quantity | 1 Set |
Table Size | 75mm x 75mm |
Voltage Supply | 230 V |
Frequency | 50 Hz |
The equipment comprises a vibratory table 75mm x 75mm motorised 230 Volts, single phase A.C. cylinderical mould 3000 cm3 and 15000 cm3, guide sleve with clamp for moulds, surcharge base plate, surcharge weight for 3000 and 15000 cm3, handle for base plate, dial gauge holder, dial gauge 0.01 mm x 25 mm travel with extension piece calibration bar 75 x 300 x 3mm.
Product Details:
Minimum Order Quantity | 1 Set |
Power | Electronic |
Usage | Auto Testing Machine |
Case Material | Wooden |
Product Details:
Minimum Order Quantity | 1 Set |
Glass cylinder size | 25ml X 0.5ml |
Operating Mode | Manual |
Set Consists of one each:-
Product Details:
Minimum Order Quantity | 1 Number |
Operating Mode | Manual |
Type | Bench Type |
Feature | Portable |
This is a bench type model which is portable, sturdy and convenient for bench mounting. The side to side movement to the carrier which can take upto 7 sieves of 20cm diameter is through a chain of gears operated by a hand wheel.
Product Details:
Minimum Order Quantity | 1 Number |
Material | SS |
Operating Mode | Automatic |
Power | 1/4 HP |
This Shaker reproduces both circular and tapping motion, Produces Circular (280-320 RPM approx) and tapping (140-160 RPM approx) motion with a uniform mechanical action which ensures accurate and dependable test results. This shaker is heavy in construction and no special foundation is required. The running parts operate in oil. A 1/4 H.P. electric motor runs the machine, the machine can accommodate six test sieves + set of Lid-pan but is supplied without sieves.
Optional Extra :Product Details:
Minimum Order Quantity | 1 Set |
Material | SS |
Operating Mode | Manual |
Capacity | 50 tonnes |
Consist of the following.